IRON FLUXcast-iron searing bench 中文

IFX-031 · Ridged grill pan · Oven finish

Pork tenderloin in a grill pan: searing a cut with no fat to give

A tenderloin is tapered, lean and easy to overcook. This run used the grill pan for the sear, then moved the whole pan to the oven, and probed every two minutes because the window is narrow.

· Published · 8 min read

Bench plate IFX-31: rim diameter, wall thickness, handle angle and measured parameters

01Abstract

Two 450 g pork tenderloins, dry brined 4 hours, were seared in tallow in a grill pan at 430 °F for six minutes total, rotating 120 degrees three times, then finished in a 190 °C oven for 9 minutes to a 61 °C core. The tapered tail was folded under and tied. The thick end read 61 °C while the tail read 68 °C at the same moment.

02Variables

Independent

  • Sear rotation: rotating 120 degrees three times in the same spot, versus flipping once

Held constant

  • Pork: 2 tenderloins, 450 g each, 4 h dry brine, silver skin removed, tail folded under and tied
  • Pan: ridged cast-iron grill pan, 6 min preheat to 430 °F, 15 g tallow
  • Oven: 190 °C, pan goes in whole, no transfer to another vessel
  • Probe every 2 minutes; pull at 61 °C core; rest 6 minutes
  • No basting, no butter

Hypothesis A pork tenderloin has almost no fat, so the sear has to come from the pan, and moving the whole grill pan into the oven is faster than transferring the meat.

03Process

  1. Remove the silver skin, fold the thin tail under the body and tie it so the thickness is even; an unfolded tail cooks to 70 °C while the centre is still 55 °C.
  2. Dry brine 4 hours, then dry the surface. Lean pork will not sear if there is any water on it.
  3. Preheat the grill pan 6 minutes to 430 °F with the tallow, then lay the tenderloins on and rotate them 120 degrees every 2 minutes — three rotations, six minutes total.
  4. Move the pan, meat and all, into a 190 °C oven for 9 minutes, probing every 2 minutes.
  5. Pull at 61 °C, rest 6 minutes, and slice on the diagonal so each piece has both a seared face and a tender centre.

04Observations

  • Rotating produced 6 distinct grill marks per tenderloin; the flipped control got 4 and had two pale bands where the meat had lifted off the ridges.
  • Tallow at 430 °F gave a deeper crust than oil at the same temperature because it stays in contact with the meat rather than running into the valleys.
  • The pan went from the hob at 430 °F into the 190 °C oven and reached the 61 °C core in 9 minutes; the carryover during the 6 minute rest took it to 64 °C.
  • Thick end 61 °C, tail 68 °C at the same moment — folding the tail under cut that difference from what would have been 15 °C to 7 °C.
  • A control tenderloin transferred to a baking tray instead of going in the pan took 12 minutes to reach 61 °C, because it lost contact heat.

Instrument log

MethodMarksTime to 61 °CThick vs tailCrust
Rotate in pan + oven69 min61 / 68 °Cdeep, continuous
Flip once in pan + oven49 min 30 s60 / 71 °Ctwo pale bands
Transferred to a tray412 min61 / 70 °Cpalest

05Conclusion

Pork tenderloin is a timing exercise in a pan that has been given nothing to work with. You supply the fat, you supply the sear, and you keep the pan in contact by moving it into the oven rather than moving the meat. Rotating 120 degrees three times gave six marks and no pale bands, and folding the tail under cut the ends-temperature spread from 15 °C to 7 °C — which is the difference between a juicy tenderloin and a dry one with a perfect middle.

Terms used